Install Guide

2019-2027 Ram 1500 Full Skid Plate Package Install Instructions

2019-2027 Ram 1500, 1500 RHO, 1500 TRX
Part #JG-RAM1500-DT-4WD-SKID-SET-TRX-BLK
Difficulty
Moderate
Steps
10
2019-2027 Ram 1500 Full Skid Plate Package
1

Safety First!

The skid plates can be installed on the ground, but if you do decide to jack up your truck to get more room for the install ALWAYS use appropriately rated jack stands. Never go underneath your vehicle on jacks alone.
2

Front Bracket Install

If there are any factory splash shields installed on your Ram behind the active air dam those will need to be removed prior to installation of the Juggernaut skid plates.

Starting with the front brackets you will need to install the provided (2) M10 clip nuts onto the brackets prior to them being installed on the vehicle. They will snap into place when the retaining clip pops into the hole in the bracket.
Front Bracket Install
3

Front Bracket Install

Once the clip nuts are installed get the provided (4) 3/8" x 1" bolts ready with a 3/8 washer on the bolt and place them through the front frame horns in the two holes shown below.

The bolts will go from the inside of the frame horn, then the bracket followed by the 3/8 washer and 3/8 nylock nut.

These bolts can be tightened to 35 ft-lbs once installed.
🔧 Torque: 35 ft-lbs
Front Bracket Install
Front Bracket Install
Front Bracket Install
Front Bracket Install
4

Engine Skid Plate Install

*If FULL SKID PLATE PACKAGE was purchased, the transmission skid MUST be installed prior to engine skid plate. Proceed to Step 7 and then install engine skids*

For engine skid plate installation start by threading (2) M10 bolts and washers into the factory frame rail threaded holes shown below. They only need to be turned a few threads in to leave exposed bolt for skid to slide onto.
Engine Skid Plate Install
5

Engine Skid Plate Install

Slide Engine skid plate over rear bolts and use (2) M10 bolts and washers to secure the front of the skid plate [circled below]. Only thread the front (2) bolts in a few threads to leave room for the front skid plate to be installed next.
Engine Skid Plate Install
6

Engine Skid Plate Install

Next you can slide the rear of the front skid plate on top of the engine skid plate as shown below.

Then use (2) M10 bolts and washers with a dab of blue loctite on the threads to secure the front of the front skid to the steel brackets installed in step 3.

*If you are only installing the Engine skid plate package you can torque the bolts down to 35 ft-lbs*

Leave bolts loose if you are doing a full skid install
🔧 Torque: 35 ft-lbs
⚠Use blue loctite on bolts that go into clip nuts
Engine Skid Plate Install
7

Transmission Skid Plate Install

Starting with the transmission crossmember, install the provided M10 flag plate into the passenger side of the crossmember as shown below.

Thread (3) M10 bolts with washers into the flag plate and the two threaded holes in the crossmember as shown below.
Transmission Skid Plate Install
Transmission Skid Plate Install
8

Transmission Skid Plate Install

Once bolts are installed on the transmission crossmember get (2) M10 bolts and washers ready for the rear engine crossmember and then slide the rear of the skid plate onto the three bolts installed in the previous step.

Once the skid is held up into place install the front (2) M10 bolts and washer into the engine crossmember [circled below]

*If doing a full skid plate install jump back to Step 4 for engine skid plate installation*
Transmission Skid Plate Install
9

Transfer Skid Plate Install

*If doing transfer case only install look at Step 7 for transmission crossmember bolt install*

The Transfer Case skid will slide onto the 3 bolts installed on the transmission crossmember. It will slide on top of the transmission skid plate.

With the Transfer Case skid held in place by the 3 crossmember bolts, line up the bolt holes on the outside of the drivers side frame rail with the factory threaded holes.

Use (2) M10 bolts and washers to secure the outside frame rail flange of the skid plate to the frame rail. Push up the skid until the back flange is resting on the frame rail and then tighten to 35 ft-lbs.
🔧 Torque: 35 ft-lbs
Transfer Skid Plate Install
Transfer Skid Plate Install
10

Tighten All Bolts

Now that all skid plate are on, tighten all M10 bolts to 35 ft-lbs.

Your skid plate installation is complete! Thank you for purchasing Juggernaut USA skid plates!
🔧 Torque: 35 ft-lbs
Tighten All Bolts
✓

Installation Complete

Enjoy your new Juggernaut USA skid plate. Built, fabricated & assembled in Colorado — backed for life.

Rather have us do it?

Our team installs these every week at our Wheat Ridge, CO shop. Skip the garage time — book a professional install and drive away dialed in.