
Ford Bronco 6th Gen Skid Plates (2021–2027): What the Factory Covers.
Our 1/4″ aluminum Bronco skid plates are here. What Ford's bash plates cover on each trim, what stays exposed, how the market compares, and which Broncos our set fits.
Ford's steel bash plates are standard on the 2026 Badlands, Stroppe and Raptor, optional on Big Bend, front-only on Heritage, and not listed on Base or Outer Banks. Sasquatch adds none of it.
Our 1/4″ aluminum Bronco set covers the engine and oil pan, transmission and transfer case (not the fuel tank). $1,219.95 as a package. Fits 2021–2027 Broncos with the 2.3L or 2.7L, and 2027s with the new 3.0L V6.
Our 1/4″ aluminum skid plates for the full-size Ford Bronco are here. The set covers the engine and oil pan, the transmission and the transfer case, and fits 2021–2027 Broncos with the 2.3L or 2.7L EcoBoost, plus 2027s with the new 3.0L V6. It does not cover the fuel tank. Prices, fitment and links are in Our Bronco skid plates.
The rest of this page covers what is under your Bronco today, what your trim already protects, and what the rest of the market sells. Ford trim content and competitor listings were checked in November 2026. Specs change, so confirm before you buy.
The Bronco Sport is a different vehicle on a unibody platform. Nothing here applies to it.
Jump to: What the factory covers · What stays exposed · What the market sells · How to judge a kit · Our Bronco skid plates · FAQ

What the factory covers, by trim
Ford's steel bash plates are standard on some Broncos, optional on others and not offered on the rest. For 2026, per Ford's own trim pages:
| 2026 trim | Factory bash plates |
|---|---|
| Base | None listed |
| Big Bend | Optional full underbody set |
| Outer Banks | None listed |
| Heritage Edition | Front section only |
| Badlands | Full underbody, standard |
| Stroppe Edition | Full underbody, standard |
| Raptor | Heavy-duty full underbody, standard |
"Full underbody" does not mean every component. When Ford itemized the set for the 2021 launch, it listed steel shields for the engine, transfer case and fuel tank, shin guards, and a front bash plate that requires the steel modular front bumper. Badlands added a stabilizer bar shield. A separate transmission plate was not on the list. Ford's current pages don't break the set down, so check your own truck.
Two things make the brochure hard to read.
The Sasquatch package is not underbody armor. It is 35-inch tires, high-clearance HOSS suspension (FOX on Badlands and Wildtrak), a 4.7 final drive and electronic locking front and rear axles. It raises the truck. It does not add bash plates. One exception to watch: on the 2026 Big Bend, Sasquatch also brings the Black Diamond package, so check that window sticker line by line.
The trim structure keeps changing. For 2026, Wildtrak returned as a package on the four-door Badlands that bundles the 2.7L EcoBoost V6, Sasquatch and the Black Appearance package. For 2027, Ford has announced a reshuffled lineup with a 3.0L V6 on several trims. Go by what is bolted to your truck, or by the window sticker, rather than the badge.
The fastest check is under the truck. Push on the panel: plastic gives under thumb pressure, steel does not. A magnet settles it. It sticks to steel and not to aluminum or plastic.
The Bronco Raptor is a separate case. It has a wider track, different suspension and its own twin-turbo 3.0L V6. Do not assume a standard Bronco plate fits it. Ours don't.
What stays exposed
With nothing under there, this is the order that follows the cost of the repair:
- Engine and oil pan. Low and forward on every Bronco engine. First contact on a bad approach.
- Transmission. Across the mid-belly, and not on Ford's itemized plate list.
- Transfer case. Hangs low, sits in the path of anything you straddle, and is expensive to replace.
- Fuel tank. Toward the rear, where breakover puts it.
- Exhaust and catalytic converter. Impact damage, and theft on a tall vehicle.

If you already have the factory steel set, the question is different. You are deciding whether to replace coated steel with aluminum that is lighter and does not rust where a rock gouges the coating.
What the market sells
The Bronco is well served. Checked against current listings in November 2026.
| Brand | Material | What the range covers | Worth knowing |
|---|---|---|---|
| Juggernaut USA | 1/4″ 5052-H32 aluminum | Package: engine and oil pan, transmission, transfer case. Each plate also sold on its own | Engine plate (and the package) comes in plastic-bumper and steel modular/Capable-bumper versions. Black powder coat, made in Colorado, Limited Lifetime Manufacturer's Warranty |
| RCI Off Road | 3/16″ steel or 1/4″ aluminum | Package: engine (two-piece), transmission, transfer case. Fuel tank plates sold separately for 2-door and 4-door | Separate packages for the 2.3L and 2.7L. Not for the Raptor |
| ASFIR 4x4 | 1/4″ (6 mm) aluminum, some steel parts in kits | Front, transmission, transfer case, fuel tank and exhaust plates sold individually. 3- and 5-piece kits cover the transmission, transfer case and crossmember (5-piece adds rear diff and lower arm guards) | Front plate is specific to the bumper you run; kits split by sway bar disconnect |
| Talons Garage | 1/4″ aluminum or 3/16″ steel | Package: front, engine, transmission, transfer case. Fuel tank plate sold separately, 4-door only | Package split by engine, bumper and (on the 2.3L) sway bar disconnect; Talons asks 2021 owners to contact them before ordering |
| Rival 4x4 | 1/4″ aluminum | Engine, transmission, transfer case, fuel tank (4-door only), sold individually | Check door count on the tank plate |
CBI Off Road and DV8 Offroad also build Bronco armor. We have not re-verified their current specs, so use their own listings.
What to take from the table:
Most Bronco builders landed on 1/4″ aluminum. It is lighter than steel, and it can't rust where a rock strips the coating. With thickness settled, compare coverage, finish and fitment.
"Package" does not describe coverage. Write down the components you want and check them against the listing. The fuel tank is the one most often left out, ours included.
Fitment splits by engine, by bumper and sometimes by sway bar disconnect. Confirm all three before you order.
How to judge a Bronco kit
The general trade-offs are in our aluminum versus steel comparison and our skid plate explainer. Five things matter on this truck.
Thickness floor. 3/16″ in steel, 1/4″ in aluminum. Strength against permanent bending grows with the square of thickness, so a 1/4″ 5052 aluminum plate takes more load before it bends than 3/16″ mild steel, at a little under half the weight. At 1/8″ or below, it is a debris cover.
Material. Steel's edge is abrasion when you drag the same plate across rock over and over. Aluminum is lighter, and it can't rust when the coating chips, which matters on a Bronco that also sees salted winter roads.
Keep or replace. If you have the factory set, decide plate by plate. A factory fuel tank plate you are not replacing should stay on.
Bumper compatibility. Front plates are designed around a specific bumper. Know whether yours is the plastic bumper, Ford's steel modular bumper, or aftermarket.
Service access. Ask whether the oil drain and filter can be reached with the plate on.

Our Bronco skid plates
We make 1/4″ 5052-H32 aluminum skid plates in Wheat Ridge, Colorado. CNC plasma cut, press-brake formed, MIG welded, powder coated black, bolt-on to factory mounting points, with all hardware included and our Limited Lifetime Manufacturer's Warranty. The photos on this page are our plates on a Bronco on our lift.
| Plate | Covers | Price |
|---|---|---|
| Skid Plate Package | Engine and oil pan, transmission, transfer case | $1,219.95 (vs $1,449.85 separately) |
| Engine Skid Plate | Engine and oil pan | $489.95 |
| Transmission Skid Plate | Transmission | $589.95 |
| Transfer Case Skid Plate | Transfer case | $369.95 |
Fitment. 2021–2027 full-size Ford Bronco with the 2.3L or 2.7L EcoBoost, and 2027 Broncos with the new 3.0L V6 (Outer Banks, Badlands, Heritage and Filson). The engine plate, and so the package, comes in two versions: one for the factory plastic front bumper and one for Ford's modular steel or Capable bumper. The last photo on the product page shows how to tell which you have. They do not fit the Bronco Raptor or the Bronco Sport. The engine, transmission and package plates will not fit a Bronco with a 4″ or taller lift, because aftermarket drop brackets and crossmembers take the factory mounting points.
What it leaves open. We don't make a fuel tank plate for the Bronco. If your truck has Ford's steel fuel tank plate, keep it on. If it doesn't, the tank is the one area our set won't cover.
Not sure which version fits? Text your year, trim and bumper to (970) 341-4221 and we'll confirm before you order. Everything is on the Bronco skid plates page, with free shipping in the lower 48.
From our bay. We run a full 4x4 install shop in Wheat Ridge, and Broncos are regulars. Recent jobs include Freedom Offroad upper control arms on a 2022 Wildtrak, a Redrock HD brush guard on a 2023 Badlands Sasquatch, and rock sliders, an intercooler and a cat-back exhaust on a 2023 Wildtrak. We fit other manufacturers' armor as well as our own. See install services.
FAQ
Do you sell Bronco skid plates?
Yes. The package covers the engine and oil pan, transmission and transfer case for $1,219.95, or you can buy each plate on its own. They fit 2021–2027 Broncos with the 2.3L or 2.7L, and 2027s with the new 3.0L V6.
Do they fit a 2027 Bronco?
Yes, with the 2.3L, the 2.7L or the new 3.0L V6 (Outer Banks, Badlands, Heritage and Filson). Not the Bronco Raptor.
Does Sasquatch include skid plates?
No. It is tires, suspension, gearing and lockers. On a 2026 Big Bend it also brings the Black Diamond package, so check the window sticker.
Will your plates fit a Bronco Raptor or Bronco Sport?
No. The Raptor has a different chassis setup and engine, and the Bronco Sport is a different vehicle entirely.
Will they fit a lifted Bronco?
Not with a 4″ or taller lift. Drop brackets and aftermarket crossmembers use the factory mounting points the plates bolt to.
Should I remove the factory bash plates before fitting aftermarket ones?
Only the ones the new plate replaces. Keep any factory plate covering a component the new kit leaves open, most often the fuel tank.
Can you install plates for me?
Yes, at our Wheat Ridge shop. Call or text (970) 341-4221.
Sasquatch is not armor. It adds tires, suspension, gearing and lockers. Underbody protection comes from the bash plate content, which is separate.
1/4″ aluminum, made in Colorado, free shipping in the lower 48. Not sure which bumper version fits? Text your year and trim to (970) 341-4221.


